Buying & choosing

Custom Multi-Size Stair and Hallway Runner: Planning a Matched Set

A custom multi-size stair and hallway runner is a matched set cut from the same broadloom carpet roll, sized separately for the stair flight, the upstairs or downstairs hallway, and any landing, so the colour and pattern run continuously through the house rather than stopping at the top step. It costs more up front than buying separate stock-size pieces because everything is cut and bound to order, but it avoids the mismatched dye lots and awkward transitions that come from buying runners piecemeal. Measure every section before ordering: a stair runner calculator handles the stair flight itself, and a stair runner length calculator adds the correct waste allowance so the whole set is cut from one continuous plan.

Start with the numbers: our stair runner calculator also works as a stair runner length calculator, adding nosing wrap, landings, winders, pattern repeat and waste so you order the right length first time.

By Sophie Ainsworth, Design editor · · 7 min read

Last updated · Reviewed by James Whitfield, Stair runner fitter and flooring estimator

Custom Multi-Size Stair and Hallway Runner: Planning a Matched Set — a tape measure laid along a stair tread

Why go custom and multi-size at all

Buying a stock-width stair runner and a separate stock-width hallway runner from different production runs almost always produces a visible seam in colour, even when both are labelled the same shade name. Dye lots vary between production batches, and different widths are often woven on different looms with slightly different tension and pile density. A custom multi-size order solves this by cutting every piece - stairs, landing, upper hallway, lower hallway - from the same broadloom roll in one order, so the colour, pile height and pattern repeat are identical throughout.

It also lets you specify a different width for each section deliberately rather than by accident. A stair runner is typically narrower than a full hallway width, and a landing sometimes needs a bespoke shape to wrap around a newel post or turn a corner - all of which is easier to plan and cut correctly from one broadloom source than to match after the fact from separate purchases.

Planning the widths for each section

SectionTypical width guidanceNote
Stair flight25-33 in (64-84 cm)26-27 in suits most 36 in (91 cm) staircases with equal margins
Upper landingSame as stair width, or full width if smallMatch stair width for visual continuity at the top
Upstairs hallway27-36 in (69-91 cm), or wall-to-wallOften slightly wider than the stair runner for a fuller look
Downstairs hallway/entry30-42 in (76-107 cm), or wall-to-wallWidest section; heaviest traffic area, budget wear rating accordingly

There is no rule that every section must be the same width - many custom sets deliberately narrow slightly for the stairs and widen again for the hallway, since a hallway usually has more open floor to fill. What matters is that the widths are decided together, on paper, before cutting starts, so the transitions at the top and bottom of the stairs look intentional rather than like an afterthought.

Stair runner width and revealA tread seen from above with equal reveals of bare wood either side of the runner, showing how runner width is derived from stair width.Stair widthRunner widthRevealReveal
Runner width and the equal margin of timber left either side of the tread.

Handling the transition points

The trickiest part of a multi-size custom order is not the stairs themselves but where one piece meets the next - typically at the top of the stairs into a landing, and at the foot of the stairs into a hallway. A change in width at these points needs a deliberate detail rather than a raw, exposed edge.

Three ways to handle a width change at a landing

Bind each piece separately and butt them together with matching binding tape, so the join reads as a clean seam. Alternatively, have the wider section's edge folded and bound to taper into the narrower stair width, which hides the step change. Or, on a generous landing, simply let the two pieces sit with a small gap of exposed floor between them, treated as a deliberate design pause rather than a mistake.

Measuring the whole run, step by step

  1. Measure the stair flight tread by tread and riser by riser, noting any winders, since these need extra pattern allowance.
  2. Measure the landing separately, including its shape if it turns a corner or wraps a newel post.
  3. Measure each hallway run in both length and width, noting doorways, radiators or built-in furniture that affect the usable width.
  4. Decide the width for each section based on the table above and your own proportions, adjusting so transitions align sensibly.
  5. Add the standard tuck allowance of 4-6 in (10-15 cm) at both ends of the stair section, plus any pattern-repeat allowance for the whole set.
  6. Total the lengths and confirm the broadloom roll width you need can be cut into every section width without excessive waste.

What it costs

Custom multi-size sets are priced by total area rather than per piece, since it is cut from one continuous broadloom roll, but expect a cutting and binding premium over a simple single-width stair runner because of the extra layout work and the additional binding needed at each transition edge.

Custom Multi-Size Stair and Hallway Runner: Planning a Matched Set — a herringbone runner on a painted staircase
ItemTypical USTypical UK
Broadloom carpet (mid-market wool-blend)$28-55 per sq ydGBP 25-48 per sq m
Custom cutting and binding, multi-piece set$6-14 per linear ft extraGBP 5-12 per linear m extra
Stair-grade underlay$4-8 per sq ydGBP 5-9 per sq m
Hallway-grade underlay$3-6 per sq ydGBP 4-7 per sq m
Fitting, stairs (straight flight)$26-52 per stepGBP 20-42 per step
Fitting, hallway and landing per linear ft/m$8-16 per linear ftGBP 8-15 per linear m

For a typical house with a thirteen-step flight, a small landing and two moderate hallway runs, total project cost commonly lands in the mid-to-upper four figures in dollars or pounds for a mid-market wool-blend, with fitting representing a larger share than on a stairs-only project because of the additional hallway length involved. Enter each section's length and width into a stair runner calculator separately, then sum the results, rather than estimating the whole project as one average per-yard figure.

Ordering and fitting sequence

Most fitters cut the stair section first, since it has the least tolerance for error and the pattern-squaring requirements discussed elsewhere apply most strictly there. The landing and hallway sections are then cut to align with the stair section's pattern position, so a directional pattern or fleck lay reads consistently as you move from stairs to landing to hallway, rather than restarting at an odd point in the repeat.

In the US, the IRC R311.7 provisions govern the stair geometry itself (tread depth, riser height, nosing) but not carpet choice; in the UK, Approved Document K (Part K) plays the same role. Neither restricts a multi-size custom carpet order, but confirming your stair geometry against these figures before the whole set is cut avoids discovering an irregular tread only after binding has already been applied to a piece cut for a standard dimension.

Know your numbers in 30 seconds

Enter your step count, tread depth and riser height — the stair runner calculator gives you the exact length to order, in metres and feet, with waste included.

Open the stair runner calculator

Whatever you decide, get the numbers first: the stair runner calculator doubles as a stair runner length calculator, adding nosing wrap, landings, winders, pattern repeat and waste so you order the right length the first time.

Still deciding on material, width or pattern? Our hub on stair runners compares weaves, widths, backings and fitting styles side by side, then hands the numbers straight to the calculator.

Frequently asked questions

Is a custom multi-size runner set more expensive than buying separate pieces?

Usually somewhat more per linear foot or metre, because of the cutting and binding premium on a multi-piece order, but it avoids dye-lot mismatches between separately purchased stock pieces, which is a real risk when buying a stair runner and hallway runner from different production batches.

Do all the pieces in a multi-size set need to be the same width?

No. It is common and often preferable to use a narrower width on the stairs and a wider width in the hallway, since hallways usually have more open floor to fill. What matters is planning every width together before cutting, so the transition points look deliberate.

How do you handle the join where a stair runner meets a wider hallway runner?

Common approaches include binding each piece separately and butting them at a clean seam, tapering the wider piece's edge to meet the narrower stair width, or leaving a small deliberate gap of exposed floor between the two as a design pause rather than a flaw.

Can a custom set include a landing that turns a corner?

Yes, and this is one of the main reasons to order a custom set rather than stock pieces - a landing that wraps a newel post or turns ninety degrees needs a bespoke shape cut to fit, which a standard rectangular stock runner cannot provide.

Should the whole house use the same carpet quality, or can hallway and stairs differ?

They can differ in wear rating if needed, but using the same broadloom roll for both, even at different widths, is what guarantees the colour and pattern match. If budget requires a cheaper quality somewhere, it is more visually forgiving to downgrade a low-traffic hallway than the stairs, which see the heaviest wear.

How much extra material should I budget for the multi-piece cutting?

Beyond the standard tuck allowance and any pattern-repeat allowance, budget a modest extra margin, typically five to ten percent of total area, to cover the additional trim waste generated by cutting several different widths from one broadloom roll rather than one continuous width.

How long does fitting a full custom multi-size set typically take?

A stairs, landing and two hallway runs project commonly takes two to four days for an experienced fitter, compared with one day for stairs alone, because of the additional measuring, cutting and binding work across multiple room transitions.

Is it worth getting a professional to measure a multi-size set rather than doing it myself?

For a stairs-only runner, a careful DIY measurement using a stair runner calculator is usually sufficient. For a full multi-size set with a landing turn or an irregular hallway shape, a professional site measure is worth the modest cost, since an error compounds across several linked pieces rather than staying contained to one flight.

Know your numbers in 30 seconds

Enter your step count, tread depth and riser height — the stair runner calculator gives you the exact length to order, in metres and feet, with waste included.

Plan my custom runner set

Ready for real prices?

Get quotes from vetted stair runner suppliers and fitters near you. Free, no account, no obligation.

Get quotes

Every guide is written from hands-on measuring and fitting experience, checked against the calculator’s own maths, and re-reviewed whenever prices or methods change. Read our editorial standards.

Keep reading